Thermos Gas Grill Parts By Category

Page instructions:  Click on any part description for photo, additional part detail and ordering.

1. "Big Easy" Triple (3-Burner) Assembly
   Fully assembled "Big Easy" three burner assembly. For units with three main burners. Includes the main burners and connecting flash tubes.
2. 16" Short Briquet Rack
   Rack which holds briquets for Charbroil 5000 and 6000 series models. This is the light gauge rack that mounts under the burner and holds the ceramic briquettes. Dimensions are 5-3/4 inches X 16 inches.
3. 20" Long Briquet Rack
   Briquet holder which helps vaporise food drippings and distribute the heat. This is the light gauge rack that mounts under the burner and holds the ceramic briquettes. Dimensions are 5-3/4" front to back X 20-1/4" wide.
4. Briquet Holder For U-Shaped Tube Burner
   Briquet holder for all models utilizing the long tube type burner. Holder measures 5-7/8 inches X 19-1/8 inches.
5. 17" Burner Assembly With 6-3/8" Tube Reach
   Top ported 2-1/4" X 17" stainless burner assembly. Venturi tube spacing is 2-3/8" center to center and tube reach is 6-3/8". Tube drop is 1-1/2".
6. 22" Burner Assembly With 6-1/2" Tube Reach
   Top ported stainless burner assembly. Dimensions are 3-5/8" X 22-1/4". Venturi tubes are permanently mounted and tube spacing is 2-3/8" center to center. Tube reach is 6-1/2".
7. 17" Burner Assembly With 4-3/4" Short Tube Reach
   Top ported 2-1/4" X 17" stainless burner assembly. Venturi tube spacing is 2-3/8" center to center and tube reach is 4-3/4". Tube drop is 1-1/2".
8. 29-1/4" U-Shaped Tube Burner and Shield
   Long "U" Shaped burner, 29 1/4" inches total length from the top of the "U" to the tube ends. Set includes the drip VapoRISER® shield, burner support bracket with mounting hardware, and burner retainer stud with clip.

1. 26-1/4" 8000 Series Traditional Style Burner Shield Drip Vaporiser Bar
   Stainless steel tent shaped drip vaporiser bar, fits Masterflame 8000 Series gas grills. 26-1/4 inches long x 4 inches wide.
2. Advantage and Performance Series Stainless Steel Heat Tent
   Vented type burner tent drip vaporizer shield. Stainless steel construction. Dimensions are 5-3/4" wide by 11-3/4" long. Sold individually, more than one required. Fits Advantage and Performance Series grills.
3. 23-1/2" Burner Shield Drip Vaporiser Bar
   Stainless steel tent shaped drip vaporiser bar. Dimensions are 23-1/2 inches long x 2-9/16 inches wide. This older style is used with the briquet holder. (See part number TH4157101).
4. 26-1/4" Burner Shield Drip Vaporiser Bar
   Stainless steel tent shaped drip vaporiser bar. Dimensions are 26-1/4 inches long x 4 inches wide.
5. 21-1/2" Burner Shield Drip Vaporiser Bar
   Stainless steel tent shaped drip vaporiser bar. 21-1/2 inches long x 2-1/8 inches wide.
6. 26-1/4" Vented Burner Shield Drip Vaporiser Bar
   Newly engineered vented style drip vaporizer bar. Dimensions are 26" X 6-1/2". Does not require the use of the briquet rack under the burner. Can be used to replace older style.

1. 8000 Series Porcelainized Cast Iron Cooking Grate Set
   Porcelain coated cast iron cook grate set. 60/40 split, large section 14-3/4" X 14-3/4", small section 14-3/4" X 11-3/4". Glossy porcelain finish.
2. Top and Bottom Tier Dual Warming Rack Set
   2-Piece warming rack set for models using dual warming racks. Top tier surface dimensions are 7-1/2" x 20" and pivot rod length 24-1/4". Bottom tier surface dimensions 9" X 21-1/2". Pivot rod length 24-7/8".
3. 23-1/2" Chrome Warming Rack
   Main warming rack. Chrome plated. Surface dimensions are 10-1/2" X 23-1/2". Pivot rod length 27-1/8". Can be used as bottom tier on dual warming rack models.
4. 26-1/4" Chrome Warming Rack
   Main warming rack. Chrome plated. Surface dimensions are 10-1/2" X 26-1/4". Pivot rod length 29-3/4". Can be used as bottom tier on dual or two tier warming rack models.
5. 22-1/8" Porcelain Coated Cooking Grid
   Heavy duty porcelain coated cooking grid. One piece, dimensions 11-7/8" W X 22-1/8" L.
6. 24" Porcelain Coated Cooking Grid
   Porcelain coated steel rod single section cooking grid. Dimensions are 14" W. X 24" L.
7. 26-1/2" Porcelain Coated Cooking Grid
   Heavy duty porcelain coated steel rod cooking grid. One piece, dimensions 14-3/4" X 26-1/2".
8. 21-1/2" Bottom Tier Warming Rack
   Chrome plated bottom tier warming rack. Surface dimensions 9" X 21-1/2". The pivot rod length which is the rod that goes into the top cover is 24-7/8" long.
9. 23-1/2" Two Tier Warming Rack Set
   For models using dual warming racks. Top tier surface dimensions are 8-1/2" X 20-3/4" and pivot rod length is 26". Bottom tier surface dimensions are 10-1/2" X 23-1/2" and pivot rod length is 27-1/8".
10. 26-1/4" Two Tier Warming Rack Set
    For models using two different level warming rack sets. Top tier surface dimensions are 9" X 24" and pivot rod length is 28-3/4". Bottom tier surface dimensions are 10-1/2" X 26-1/4" and pivot rod length is 29-3/4".

1. Big Easy Main Ignitor Wire
   Big Easy main ignitor wire. 15" long with round connector at wire end and flat connector at ceramic end.
2. Two Pole Electronic Spark Module Assembly
   Electronic spark generator with 2 connectors. Includes locking ring, push button and battery. Fits models with sideburner using a two wire connection. Channel #1740-37.
3. Single Pole Snap-In Ignitor Push Button
   Snap-In ignitor push button for units without side burners. (Single pole. Uses one wire.) Wire not included.
4. Double Pole Snap-In Ignitor Push Button
   Snap-in 2 pole pushbutton for units with sideburners.Uses two wires. One connects at bottom with a round connector and the other at the side with a flat connector.
5. Eleven Inch Ignitor Wire
   Ignitor wire with one round connector and one flat spade connector. Measure 11 inches long.
6. Button assembly for electronic module
   Rubber button assembly with chrome locking ring for electronic ignitor component.
7. Igniter Kit with Collector Box, Electrode and Wire
   Burner igniter kit. Includes the twist and lock collector box, electrode and connector wire. Does not include push button. Instructions
8. Burner Ignitor Kit
   Includes the twist and lock collector box, electrode, mounting screw and connector wire. Used on 1999 and newer Masterflame burners. Instructions
9. Double Pole Rotary Spark Generator
   Rotary spark generator with knob and screws. Double pole generator uses two wires. Knob snaps and locks onto generator shaft.

1. Big Easy Burner Tent Support
   Support assembly for the Big Easy burner tent. Holds the 6" X 6" burner tent over the burner. More than one required.
2. Black Control Knob
   Black gas control knob.
3. Big Easy Gas Control Knob
   Black plastic main gas control knob for the Big Easy. Knob is 2 inches tall and 2-1/2" in diameter at the base of the knob.
4. Button assembly for electronic module
   Rubber button assembly with chrome locking ring for electronic ignitor component.
5. "Grease Catcher" Hanger Wire and Cup
   Aluminum grease catcher cup which hangs under the grill to catch excess drippings. Includes hanger which threads through the drip hole in the bottom of the casting
6. Millennium Style 17-1/8" Grill Lid Handle
   Large curved black handle with mounting holes measuring 14-1/2" center to center. The handle measures 17-1/8" side to side and stands out from the grill 4".
7. Alpine Style 11-1/2" Lid Handle
   Alpine Lid Handle Replacement Kit. Kit includes mounting screws and gasket. Mounting holes 8-7/8" on center. Dimensions 11-1/2" X 4-1/4".
8. Propane Grill Regulator End Fitting
   New style Type QCC regulator end fitting. Large black new style coupling nut with 1/2" outside diameter male pipe thread which screws into the regulator.
9. CHARBROIL HANDLE,FRT,PLAS,MILL JR,8.80" CTR,BLK,01
   CHARBROIL HANDLE,FRT,PLAS,MILL JR, 8.80" CTR,BLK,01 (No Hdw)
10. 17" Burner Assembly With 6-3/8" Tube Reach
    Top ported 2-1/4" X 17" stainless burner assembly. Venturi tube spacing is 2-3/8" center to center and tube reach is 6-3/8". Tube drop is 1-1/2".
11. 17-1/8" Black Plastic Grill Lid Handle
    Large curved black handle with mounting holes measuring 14-1/2" center to center. The handle measures 17-1/8" side to side and stands out from the grill 4". Handle is molded with mounting studs. Hex nuts are included.
12. Double Pole Rotary Spark Generator
    Rotary spark generator with knob and screws. Double pole generator uses two wires. Knob snaps and locks onto generator shaft.

1. 18" Grill Brush
   Long handled 18" grill brush keeps your hand away from hot cooking surfaces. Hardwood handle with wide cleaning head. Constructed of brass bristles which will not damage porcelain coated surfaces.
2. Weber 21" Round Brass Bristle Grill Brush
   New design brush is constucted of stiff brass bristles which help tackle tough baked on food. Barrel design for easy cleaning in between cooking grate bars and an extra long 21" handle to keep your hand away from the heat.
3. Meat Temperature Thermometer
   The only sure way to guarantee perfect BBQ every time is to check the internal meat temperature. Quick read thermometer with 5-1/2" probe. Measures 140 - 550 degrees. Manufactured by Weber Stephens.